DOUGIE'S WHEELIE BIKE REVEALED AS RED BULL ATHLETE ATTEMPTS TO WHEELIE ENTIRE IOM TT COURSE
MANCHESTER, GREAT BRITAIN
As previously announced Red Bull athlete Dougie Lampkin will take on one of his toughest ever challenges, even in the context of his long and illustrious career, when he attempts to wheelie continuously around the entire Isle of Man TT course on Saturday 24th September 2016. This momentous occasion will be shown LIVE on Red Bull TV, when viewers from around the globe have their first ever opportunity to watch LIVE TV coverage of the mountain course as Dougie bravely endeavours to navigate the two hundred plus corners that lay ahead of him.
In order to complete this challenge Dougie and his engineering team led by Francesc Romani and Blackie Holden have spent the last 6 months creating a specially modified bike for the task in hand, as it simply would not be possible to ride solely on the rear wheel for 37.7 miles around the undulating and World famous Isle of Man TT course on a standard trial bike. Using a Vertigo Combat Ice Hell - 300cc Fuel injected single cylinder two-stroke (click here for full specification) as the base machine, the following modifications have been made thanks to the support of the Vertigo factory in Spain and Hope Technology in the UK:
1: Front wheel - 36v electric motor fitted to the hub in order to keep the front wheel spinning throughout the duration of the challenge. This is vitally important as the gyroscopic effect creates the required stability and allows the bike to be steered despite the front wheel being lofted throughout. Power to the front wheel can be controlled by a tension wire connected to the chest of the rider - whilst the wheel will always be spinning - its speed can be varied by body position to compensate for the undulating nature of the course, this helps the overall control of the bike. During testing an auxiliary battery has been used to power the front wheel motor, but in order to reduce weight and to ensure power during the entire 2 hours the bike's step-up box has been modified to directly power the motor.
2: Front brake - The standard front disc / caliper and master cylinder has been completely removed as it has no purpose. However, a modified master cylinder has been fitted on the right hand side of the handlebar (where the front brake would normally be located) that actually operates the rear brake. See rear brake for more details.
3: Front forks - As per the front brake, the front suspension has no purpose for this particular challenge, hence the standard internals have been removed and replaced with an almost rigid set up that is much lighter. The weight saving is designed to reduce fatigue to the upper body throughout the 2-hour challenge.
4: Fuel Injection - The electronic mapping has been re-mapped to optimise fuel consumption and to produce a smooth power delivery within a confined range that allows the height of the front wheel to be carefully and consistently controlled throughout.
5: Gearbox - Changes to the front and rear sprockets means that the majority of the course can be ridden in one gear, with the number of gear changes being limited due to the instability this causes. A modified sixth gear has been fitted to cope with the additional strain and the oil flow / level within the gearbox has been modified to compensate for the angle at which the bike will be operated for the 2-hour period.
6: Fuel tank - The standard 2.7 litre fuel tank that is mounted under the seat area on the bike does not have sufficient capacity to allow the 37.7 miles to be covered without refuelling. A secondary handmade carbon fibre fuel tank has been made to increase the capacity to 5 litres to provide the required range. This secondary tank is mounted in the centre of the bike to minimise the impact that the change in fuel load will cause over the duration of the challenge. The carbon fibre structure has been extended rearwards and is hollow towards the back section to house the additional electronics to power the front wheel motor and to provide a suitable surface area to allow knee contact that aides the steering process and stability especially in the case of side-winds on the exposed sections of the mountain part of the course.
7: Rear shock - The internals and spring on the rear shock has been modified in order to create a much stiffer set-up than normal, with the travel being limited to a fraction of its normal range to ensure stability and to cope with the extra load through the rear wheel.
8: Rear brake - The riding position has been moved from the standard footrest location to specially adapted footplates attached to the rear wheel spindle. Hence the position of the rear brake pedal and master cylinder has also been moved to the same place and mounted on a specially designed and CNC produced aluminium mounting plate. The same plate also houses two separately operated rear brake calipers. The first is operated by foot via the newly located rear brake pedal and second via the hand operated lever on the right hand side of the handle bar where the front brake would normally be located. The two independent systems not only help prevent rider fatigue, as the operation can be shared via foot and hand, but more importantly the design prevents overheating of the brake fluid in each system as the load can be split on the more demanding descents on the course when the rear brake will be used extensively to control the bike.
Click here for more information about the challenge itself including timings and TV viewing details.
Click here to learn why Dougie has decided to take on this unique challenge